其實早就應該養成一個良好的程序備份習慣，現在放在這里即方便自己隨時在其他地方調用、備份，也可以幫到需要的人。
對于stc自帶EEPROM來說，用起來唯一不太方便的地方就是每次修改任何一個字節需要將整個扇區都擦除才能修改，所以每次修改都要講整個扇區內容用數組全部讀出緩存起來，進行擦除操作，講需要修改的內容在相應的數組位置修改好，再講整個數組內容重新寫入到EEPROM里，頭文件中我已經將接口函數都寫好啦。直接調用就行，不用考慮任何問題，而且地址也直接從0開始到 USING_CHAR_NUM-1（USING_CHAR_NUM最大可到512）

EEPROM.h-----------------------------------------------------------------------------------------------------
#ifndef __EEPROM_H__
#define __EEPROM_H__

unsigned char EepromReadByte(unsigned char addr);

void EepromWriteByte(unsigned char addr, unsigned char dat);
#endif

EEPROM.c-----------------------------------------------------------------------------------------------------
#include "intrins.h"
typedef unsigned char BYTE;
typedef unsigned int WORD;

sfr  IAP_DATA      =   0xC2;               //Flash data register
sfr  IAP_ADDRH     =   0xC3;              //Flash address HIGH
sfr  IAP_ADDRL     =   0xC4;              //Flash address LOW
sfr  IAP_CMD       =   0xC5;              //Flash command register
sfr  IAP_TRIG      =   0xC6;              //Flash command trigger
sfr  IAP_CONTR     =   0xC7;              //Flash control register

#define   CMD_IDLE      0                 //Stand-By
#define   CMD_READ      1                 //Byte-Read
#define   CMD_PROGRAM   2                 //Byte-Program
#define   CMD_ERASE     3                 //Sector-Erase

#define   ENABLE_IAP    0x82              //if SYSCLK<20MHz
//Start address for STC12C5A60S2 series EEPROM
#define   IAP_ADDRESS   0x0000
#define      USING_CHAR_NUM   11

void IapIdle();
BYTE IapReadByte(WORD addr);
void IapProgramByte(WORD addr, BYTE dat);
void IapEraseSector(WORD addr);

unsigned char EepromReadByte(unsigned char addr)
{
    return(IapReadByte(addr));
}

void EepromWriteByte(unsigned char addr, unsigned char dat)
{
    unsigned char eepromBUF[USING_CHAR_NUM];
    unsigned char i;
    for(i=0; i< USING_CHAR_NUM; i++)
    {
        eepromBUF[IAP_ADDRESS+i] = IapReadByte(IAP_ADDRESS+i);  
    }
    if(addr < USING_CHAR_NUM)
    {
        eepromBUF[IAP_ADDRESS+addr] = dat;
        IapEraseSector(IAP_ADDRESS);

        for(i=0; i< USING_CHAR_NUM; i++)
        {
            IapProgramByte(IAP_ADDRESS+i, eepromBUF[IAP_ADDRESS+i]);  
        }
    }
}
//void EepromInit(void)
//{
//    unsigned int tmp = 0;
//    _nop_();
//    _nop_();
//    _nop_();
//    tmp = IapReadByte(IAP_ADDRESS+1);
//    tmp = (tmp << 8) + IapReadByte(IAP_ADDRESS);
//    if(0xffff == tmp)
//    {
//        IapProgramByte(IAP_ADDRESS,(BYTE)0);
//        IapProgramByte(IAP_ADDRESS+1,(BYTE)0);
//        tmp = 0;  
//    }
//    tmp++;
//    IapEraseSector(IAP_ADDRESS);
//    IapProgramByte(IAP_ADDRESS,(BYTE)tmp );
//    IapProgramByte(IAP_ADDRESS+1,(BYTE)(tmp>>8) );
//      
//}

void IapIdle()
{
      IAP_CONTR = 0;      //Close IAP function
      IAP_CMD = 0;            //Clear command to standby
      IAP_TRIG = 0;                      //Clear trigger register
      IAP_ADDRH = 0x80;                 //Data ptr point to non-EEPROM area
      IAP_ADDRL = 0;                     //Clear IAP address to prevent misuse
}

BYTE IapReadByte(WORD addr)
{
      BYTE dat;                          //Data buffer
      IAP_CONTR = ENABLE_IAP;   //Open IAP function, and set wait time
      IAP_CMD = CMD_READ;        //Set ISP/IAP/EEPROM READ command
      IAP_ADDRL = addr;                 //Set ISP/IAP/EEPROM address low
      IAP_ADDRH = addr >> 8;      //Set ISP/IAP/EEPROM address high
      IAP_TRIG = 0x5a;                //Send trigger command1 (0x5a)
      IAP_TRIG = 0xa5;                  //Send trigger command2 (0xa5)
      _nop_();  _nop_();                          //MCU will hold here until ISP/IAP/EEPROM
      //operation complete
      dat = IAP_DATA;            //Read ISP/IAP/EEPROM data
      IapIdle();                         //Close ISP/IAP/EEPROM function
      return dat;                        //Return Flash data
}

void IapProgramByte(WORD addr, BYTE dat)
{
  IAP_CONTR = ENABLE_IAP;         //Open IAP function, and set wait time
      IAP_CMD = CMD_PROGRAM;     //Set ISP/IAP/EEPROM PROGRAM command
      IAP_ADDRL = addr;                 //Set ISP/IAP/EEPROM address low
      IAP_ADDRH = addr >> 8;            //Set ISP/IAP/EEPROM address high
      IAP_DATA = dat;                  //Write ISP/IAP/EEPROM data
      IAP_TRIG = 0x5a;                   //Send trigger command1 (0x5a)
      IAP_TRIG = 0xa5;                   //Send trigger command2 (0xa5)
      _nop_();   _nop_();                        //MCU will hold here until ISP/IAP/EEPROM
      //operation complete
      IapIdle();
}

void IapEraseSector(WORD addr)
{
      IAP_CONTR = ENABLE_IAP;  //Open IAP function, and set wait time
      IAP_CMD = CMD_ERASE;      //Set ISP/IAP/EEPROM ERASE command
      IAP_ADDRL = addr;                //Set ISP/IAP/EEPROM address low
      IAP_ADDRH = addr >> 8;         //Set ISP/IAP/EEPROM address high
      IAP_TRIG = 0x5a;                   //Send trigger command1 (0x5a)
      IAP_TRIG = 0xa5;                   //Send trigger command2 (0xa5)
      _nop_();  _nop_();                         //MCU will hold here until ISP/IAP/EEPROM
      //operation complete
      IapIdle();
}