1. 用C語言編程，利用定時器產生一個0~99秒變化的秒表，并且顯示在數碼管上，每過一秒將這個變化寫入實驗板上AT24C02，當關閉實驗板電源，并再次打開實驗板電源時，單片機從AT24C02中將原來寫入的數據讀出來，接著繼續變化在數碼管上。
#include
#define uchar unsigned char
#define uint unsigned int
//=========全局變量區============================================
bit write=0; //寫24C02的標志；
sbit sda=P2^0;
sbit scl=P2^1;
sbit high=P2^4;
sbit mid=P2^3;
sbit low=P2^2;
uint code NumTable[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71};//數字的編碼
uchar sec,tcnt;
uchar code table[]={
0x3f,0x06,0x5b,0x4f,
0x66,0x6d,0x7d,0x07,
0x7f,0x6f,0x77,0x7c,
0x39,0x5e,0x79,0x71
};
//=========全局變量區結束============================================
/**
步驟
接線方式：
1、P0接數碼管J12,實現段選
2、譯碼器和數碼管位選輸入短接，J15+J16
3、本實驗使用的晶振是12.000
**/
//========函數區============================================
void delay()
{;;}
void delay1ms(uint z)
{
uint x,y;
for(x=z;x>0;x--)
for(y=110;y>0;y--);
}
/**
延時
**/
void delay_1ms(uint x){
uint i=x;
uint j;
for(;i>0;--i){
for(j=110;j>0;--j);
}
}
/**
在數碼管上顯示對應的值
**/
void display(uchar Num)
{
P0=NumTable[Num];
delay_1ms(1);
P0=0; //送完段選信號后，進行消影的處理
}
/**
控制數碼管顯示后3位，并分解計數值
**/
void DisplayNumByOrder(uint Value){
low=0; mid=0; high=0; display(0);
low=1; mid=0; high=0; display(0);
low=0; mid=1; high=0; display(0);
low=1; mid=1; high=0; display(0);
low=0; mid=0; high=1; display(0);
low=1; mid=0; high=1; display(Value%1000/100);
low=0; mid=1; high=1; display(Value%100/10);
low=1; mid=1; high=1; display(Value%10);
}
void start() //開始信號
{
sda=1;
delay();
scl=1;
delay();
sda=0;
delay();
}
void stop() //停止
{
sda=0;
delay();
scl=1;
delay();
sda=1;
delay();
}
void respons() //應答
{
uchar i;
scl=1;
delay();
while((sda==1)&&(i<250))i++;
scl=0;
delay();
}
void write_byte(uchar date)
{
uchar i,temp;
temp=date;
for(i=0;i<8;i++)
{
temp=temp<<1;
scl=0;
delay();
sda=CY;
delay();
scl=1;
delay();
}
scl=0;
delay();
sda=1;
delay();
}
uchar read_byte()
{
uchar i,k;
scl=0;
delay();
sda=1;
delay();
for(i=0;i<8;i++)
{
scl=1;
delay();
k=(k<<1)|sda;
scl=0;
delay();
}
return k;
}
void write_address(uchar address,uchar date)
{
start();
write_byte(0xa0);
respons();
write_byte(address);
respons();
write_byte(date);
respons();
stop();
}
uchar read_address(uchar address)
{
uchar date;
start();
write_byte(0xa0);
respons();
write_byte(address);
respons();
start();
write_byte(0xa1);
respons();
date=read_byte();
stop();
return date;
}
void init()
{
sda=1;
delay();
scl=1;
delay();
sec=read_address(2); //讀出保存的數據賦于sec
if(sec>100) //防止首次讀取出錯誤數據
sec=0;
TMOD=0x01; //定時器工作在方式1
ET0=1;
EA=1;
TH0=(65536-50000)/256;//對TH0 TL0賦值
TL0=(65536-50000)%256;//使定時器0.05秒中斷一次
TR0=1; //開始計時
}
void main()
{
init();//初始化
while(1)
{
DisplayNumByOrder(sec);
if(write==1) //判斷計時器是否計時一秒
{
write=0; //清零
write_address(2,sec); //在24c02的地址2中寫入數據sec
}
}
}
//========函數區結束============================================
//========中斷函數區============================================
void t0() interrupt 1//定時中斷服務函數
{
TH0=(65536-50000)/256;//對TH0 TL0賦值
TL0=(65536-50000)%256;//重裝計數初值
tcnt++; //每過50ms tcnt加一
if(tcnt==20) //計滿20次（1秒）時
{
tcnt=0; //重新再計
sec++;
write=1; //1秒寫一次24C02
if(sec==100)//定時100秒，再從零開始計時
sec=0;
}
}
//========中斷函數區結束============================================
下載文檔
