PLC編程中有大量的定時器和計數器可用,做工業自動化控制的朋友在LABVIEW編程時經常因?yàn)檎也坏筋愃剖煜さ墓δ芏鵁?其實LABVIEW本身提供的邏輯功能非常強大,遠遠超過PLC.看看加計數器的說明:它有兩個控制端initialize--是計數器復位端,相當于PLC計數器的resetactivate----計數控制端,當ACTIVATE=TRUE時,每調用一次,計數器內部計數加1.兩個輸出端:Counter---輸出計數器當前計數,U32數據類型,最大計數范圍0XFFFFFFFFOverflow---溢出,當超過計數器最大計數,為真,計數器自動復位,重新從1開始計數.應用舉例:記錄SUBVI被調用的次數加計數器的程序框圖減計數器基本類似,更為常用,比如計數器10次觸發一次事件,就減計數器就非常合適,就不詳細介紹了Data Queue是一個非常重要的VI,仔細分析它的程序結構,他實際上是一個先進先出的緩沖區(FIFO BUFFER)它默認的是一個DOUBLE類型的輸入,改動一下,就可以適應各種數據類型(重用LABVIEW的VI是一個重要的編程方法)程序框圖

initialize, when TRUE, initializes the internal state of the VI.input data point is an input data point.sample length is the length of each set of incoming data. The VI processes each set of data. The default is 100. sample length must be greater than zero.eliminated element is the first point eliminated from the queue.Current Queue is the new array created by eliminating the first point and appending the new point.Previous Queue is the set of data before any operation in this call.error returns any error or warning from the VI. You can wire error to the Error Cluster From Error Code VI to convert the error code or warning into an error cluster.current length is the size of the current queue應用舉例:XY GRAPH如果顯示一個不斷變化的曲線那,改造這個VI,DOUBLE輸入改造成簇,包括X,Y,代表一個點,在程序循環中不斷加入新點,這樣一個XY GRAPH就變成了類似CHART的圖表了.